User Tools

Site Tools


spark_timelapse

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

spark_timelapse [2019/11/22 02:05]
peter created
spark_timelapse [2019/11/29 00:31] (current)
peter
Line 1: Line 1:
-=====Spark系统打印录像管理=====+=====Spark ​system print recording management=====
 \\ \\
-Spark的主界面进入自动录像面板(Timelapse)面板后,可设置自动录像的模式,以及查看已生成的录像视频。\\ +After entering the Timelapse panel from the main interface of Spark, you can set the automatic recording mode and view the generated recording video.\\ 
-Spark的录像模式有两种定时录像(Timed)和逐层录像(On Z Change):\\+Spark has two recording modes: Timed and On Z Change\\
 \\ \\
 {{:​spark_timelapse_1.jpg?​nolink|}} {{:​spark_timelapse_1.jpg?​nolink|}}
 \\ \\
 \\ \\
-====定时录像模式==== +====Timer recording mode==== 
-定时录像模式是每隔一段时间,拍摄一张快照,然后将所有照片合并生成视频。\\+Timed recording mode is to take a snapshot every time, and then combine all photos to generate a video.\\
 \\ \\
 {{:​spark_timelapse_2.jpg?​nolink|}} {{:​spark_timelapse_2.jpg?​nolink|}}
 \\ \\
-定时录像的设置参数有:\\ +The setting parameters of timing recording are:\\ 
-Snapshot interval: ​生成快照的间隔时间\\ +Snapshot interval: ​Time between snapshots\\ 
-Timelapse frame rate: 视频每秒钟的帧数,按每10秒1张快照,每秒25帧计算,1小时的打印生成的视频长度为14.4\\ +Timelapse frame rate: The number of frames per second of the video, calculated as snapshot every 10 seconds and 25 frames per second. The length of the video generated by hour of printing is 14.4 seconds.\\ 
-Timelapse post roll: 视频结束时,最后一张照片的展示时长\\+Timelapse post roll: How long the last photo was shown at the end of the video\\
 \\ \\
-设置完成后,在Save as default前打上勾,然后点击Save changes\\+After the settings are complete, check the box before ​Save as default, and then click Save changes\\
 \\ \\
 ---- ----
-====逐层录像模式==== +====Layer-by-layer recording mode==== 
-逐层录像模式是每打印一层,拍摄一张快照,然后将所有照片合并生成视频。\\ +The layer-by-layer recording mode is to print a layer, take a snapshot, and then combine all the photos to generate a video.\\ 
-**请注意,逐层录像模式仅支持打印Spark系统中的GCode文件,不支持打印SD卡内的GCode文件**+**Please note that the layer-by-layer recording mode only supports printing GCode files in the Spark system, and does not support printing ​GCode files in the SD card.**
 \\ \\
 {{:​spark_timelapse_3.jpg?​nolink|}} {{:​spark_timelapse_3.jpg?​nolink|}}
 \\ \\
-逐层录像的设置参数有:\\ +The setting parameters of layer-by-layer recording are:\\ 
-Minimum interval: ​每层打印的最短时间,如果打印一层的时间小于该数值,则不会生成快照\\ +Minimum interval: ​The minimum time to print each layer. If the time to print one layer is less than this value, no snapshot will be generated.\\ 
-Timelapse frame rate: 视频每秒钟的帧数,按0.15mm层高,每秒25帧计算,打印10cm高的模型生成的视频长度为26.7\\ +Timelapse frame rate: The number of frames per second of the video is calculated based on the 0.15mm ​layer height and 25 frames per second. The length of the video generated by printing a 10cm high model is 26.7 seconds.\\ 
-Timelapse post roll: 视频结束时,最后一张照片的展示时长\\ +Timelapse post roll: How long the last photo was shown at the end of the video\\ 
-Retraction Z-Hop: ​回抽时喷头上头,WEEDO 3D打印机不支持该功能,请将该数值设置为0\\+Retraction Z-Hop: ​The nozzle is on the head during the pumping. The WEEDO 3D printer does not support this function. Please set the value to 0.\\
 \\ \\
-设置完成后,在Save as default前打上勾,然后点击Save changes\\+After the settings are complete, check the box before ​Save as default, and then click Save changes\\
 \\ \\
 ---- ----
-====视频文件管理==== +====Video file management==== 
-打印完成后自动生成的录像视频文件展示在下面的列表中\\ +The video files generated automatically after printing are shown in the list below\\ 
-视频文件名为打印文件名加打印时间,点击文件名列表最右侧的下载图标,可将视频下载到本地电脑上进行观看\\ +The video file name is the print file name plus the print time. Click the download icon on the far right of the file name list to download the video to your local computer for viewing.\\ 
-点击文件名列表右侧的删除图标, 可以删除该视频文件\\+Click the delete icon to the right of the file name list to delete the video file\\
 \\ \\
 {{:​spark_timelapse_4.jpg?​nolink|}} {{:​spark_timelapse_4.jpg?​nolink|}}
spark_timelapse.txt · Last modified: 2019/11/29 00:31 by peter